Skip to main content
B&B Mechanical — commercial HVAC in Lakeside, CA
Learning Center · Learn

Cooling Tower Fill Fouling and Scale: Why Approach Climbs

Fouled fill is the most common reason a tower stops cooling. The first sign is a climbing approach, not a failure.

By B&B Mechanical Team Published

What fill does

Fill is the honeycomb media inside a cooling tower that spreads water into thin films so air can evaporate it. When fill is scaled or fouled, less water meets air and the tower rejects less heat.

How it happens

  • Mineral scale from San Diego County’s hard municipal makeup water.
  • Biological growth where water sits warm and slow.
  • Debris and dust pulled in through the air inlets.
  • Uneven water distribution from plugged nozzles.

How it shows up

Approach temperature climbs at the same load, chillers run closer to high head pressure, and fans run longer. The tower has not failed; it has lost capacity.

What repair restores

Cleaning or replacing fill, clearing nozzles and basins, correcting water distribution and checking the drive. Where fill has collapsed or the structure is corroded, the repair-or-replace comparison follows.

What the technician looks for inside the tower

A fill inspection is visual and physical. Fill is checked for scale weight and sag, nozzles for plugging, the basin for sediment and the distribution for dry spots that mean water is channeling instead of spreading.

How water quality drives the schedule

San Diego County’s municipal water carries dissolved minerals that concentrate as the tower evaporates. The building’s water treatment provider manages chemistry and blowdown; B&B’s inspections show whether that program is keeping scale off the fill. The two work together, and neither replaces the other.

Repair, clean or replace fill

  • Clean: light scale and debris, nozzles cleared, distribution corrected.
  • Replace fill: heavy scale, collapsed or brittle media; the tower structure is sound.
  • Replace the tower: corroded structure or basin, failed drive components alongside fouled fill, or capacity that no longer matches the chiller.

The decision is written up with the readings that support it.

Frequently Asked Questions

Can fill be cleaned in place?

Light scale sometimes; heavy or collapsed fill is replaced.

Does fouling damage the chiller?

Indirectly. Warmer condenser water drives head pressure up and the chiller works harder or trips.

How often should fill be inspected?

At each maintenance visit, with a closer look before summer.

Can fouled fill damage the fan or drive?

Indirectly. A tower losing capacity runs its fan longer and harder, which wears the drive, belts and bearings sooner.

How quickly can approach recover after fill work?

Immediately on the next load, if fill was the cause. If approach stays wide, the problem is elsewhere, usually water distribution or airflow.

Terms used in this guide

Approach Temperature
Approach temperature is the difference between the water leaving a cooling tower and the outdoor wet-bulb temperature, and it's the single best number for tracking a tower's health over time. A tower in good condition holds a fairly consistent approach; a steadily rising approach signals degrading heat transfer.
Cooling Tower Range
Range is the temperature drop across a cooling tower: hot condenser water in minus cooled water out. Range is set by the heat the chiller rejects and the water flow; a collapsing range usually points to a flow problem, not the tower itself.
Wet-Bulb Temperature
Wet-bulb temperature is the lowest temperature air can reach through evaporation at its current humidity. It sets the floor for how cold a cooling tower can make its water, which is why towers are rated against design wet-bulb, not dry-bulb, conditions.
Makeup Water
Makeup water replaces what a cooling tower loses to evaporation, drift and blowdown, and what a closed hydronic loop loses to leaks. A rising makeup meter on a closed loop is a leak indicator; on a tower it tracks load and water quality.
Have a question?

Talk to a real technician.

Tell us what's going on and our San Diego team will reach out. For emergencies, call us 24/7 at (619) 713-0400.

Call us 24/7(619) 713-0400
  • 24/7 Emergency Service
  • Licensed & Insured
  • 5.0★ Rated on Google
  • Based in Lakeside, CA

10031 Maine Ave, Lakeside, CA 92040

Request a quote

Request your service

No obligation. We never sell your info.

Request Service

Tell us what's going on and our San Diego team will reach out. For emergencies, call us 24/7 at (619) 713-0400.

Loading form. If it does not load, please use the other contact options on this page.

By submitting, you agree to our Privacy Policy and Terms & Conditions. If you opt in to texts, message & data rates may apply and you can reply STOP to opt out.

Call Now Request Service